SERVO SAM 5 Bed-Type Mill

SAM 5

Three-Axis Bed-Type CNC Milling Machine

Rigid, stable, precise.
Supports heavier work pieces.
No CNC: experience required
Upgradeable to four axes.

Machine Features

5 HP with 40 taper spindle head (uses NMTB 40 tooling)
Travel XYZ (36" x 20" x 21.5")
Work surface (14" x 54")
Z-axis counter-balanced for quicker movement, and longer motor/screw life
Inverter-driven spindle drive motor
Precision ground ball screws (XYZ)
Power spindle drawbar standard
Hardened and ground square ways with turcite finish
Way covers (YZ)
Heavy Meehanite castings
Full manual mill capability
Teach/Conversational/CNC programming capabilities
CAD/CAM compatible

Shown with optional equipment.

SAM 5 SPECIFICATIONS

Spindle Head

5 HP TEBC motor	Spindle (rpm) 50-500(back gear)	Power drawbar
40 NST taper spindle (uses NMTB 40 tooling)	500-5,000(direct drive)	Quill travel (manual) 5"
Solid-state adjustable frequency AC drive (UL-approved)	Spindle balanced with Class 7 Fafnir Bearings

Table, Saddle and Head

Work surface (table) 14" X 54"	Peak torque 165 in./lb.	Dovetail table ways, X axis
Tee slots (4) 5/8" on 2-1/2" ctrs.	Continuous torque 115 in./lb.	hardened and ground with turcite finish
CNC feed rate .01 to 100 IPM	Table load capacity 1,000 lbs.	Wide square box-type ways, Y axis
Rapid rate (X & Y) 190 IPM (Max)	Head tilt ± 45°.	hardened and ground with turcite finish
Table travel (X axis) 36" (31" over saddle)	VR brushless DC axis drive motors	Square box-type knee ways, hardened
Saddle travel (Y axis) 20"	1-1/4" dia. precision ground ball screws	and ground with turcite finish
Head travel (Vertical) 21.5"	and angular duplex bearings (XYZ)	Auto lube system

Standard Control

MS-DOS-based system (installed)	14" VGA color monitor	One RS-232 serial port
586-75 MHz processor	1.44 MB 3-1/2" floppy drive	Full 101-key keyboard
8MB RAM (random access memory)	1 GB hard drive	Enclosed with swivel mounting arm

Dimensions/Electrical Requirements

Overall machine dimensions (footprint)	93'h x 112" w x 70"d
Electrical: Spindle motor	220 VAC, 3 phase, 60Hz, 30amps
Axis drive motors	220 VAC,1 phase, 60 Hz, 20 amps
Servo Operator Console	110 VAC, 1 phase, 60 Hz, 5 amps, filtered and grounded

SAM 5 Options

Automatic spindle speed control with brake	Quick'n'Easy CAM/CNC utilities	M-7 controlled outlet (220 VAC, 1 ph.)
Automatic flood coolant system	Fourth-axis 10" diameter rotary table

About the Servo Control

Full Manual Capability: (System on/drives free.) Allows you to use handwheels to move X, Y and Z. Or, use handheld pendant to move each axis under power, control direction and feed rate. In either of these situations, system reads each axis position on CRT
Teach Pendant Mode: Easy-to-use handheld pendant lets you teach XYZ point-to-point and angular part moves. Jog moves range from .0005" to .050" for precise positioning. You can select rapid or feed rate moves, single step through programs, set and clear axis limits, plus store up to four subroutines in memory.
Conversational Programming Mode: Provides full prompt menus and help screens so anyone with a knowledge of reading blueprints can program in this software mode. Features include graphic tool path verification, real-time graphics, automatic cycles (pocket clear, bolt hole patterns, etc.), absolute/incremental programming, inch/metric programming, automatic corner radius, backlash compensation, fixture/axis offsets, and more.
CNC Mode: G & M code programming with features such as XY, XZ, and YZ circular interpolation, up to 4-axis linear interpolation, tool select, scaling/mirror image, cutter diameter compensation, axis position preset, continuous contouring, helical interpolation, backlash compensation, tool length offset and fixture offset.

Made in U.S.A

SERVO PRODUCTS COMPANY

433 N. Fair Oaks

Pasadena, CA 91103 USA

For more information Email denver@corrick.com

Denver Corrick, Webmaster 01/13/99
Copyright © 1995 Servo Products Co.. All rights reserved.
Information in this document is subject to change without notice.
Other products and companies referred to herein are trademarks or registered trademarks of their respective companies or mark holders.